goniometer

1. Goniometer rAn instrument used in measuring angles.: 角度计-用来测量角度的设备。

2. Cervical range of motion and pressure pain thresholds were measured using a goniometer and an algometer.: 颈活动度和压痛阈用关节角度计和痛觉计进行测量。

3. This paper studied a kind of automatic test technology of the parameters used in a dual-CCD TV goniometer.: 本文研究的是一种由双CCD构成的电视测角仪的参数自动检测技术。

4. PC_401 computer system was introduced to the double crystal goniometer for small Angle scattering measurement.: 对双晶衍射仪实行改造，用一台PC _ 401微机直接控制和进行小角散射等测量。

5. MethodsThe ranges of abduction motion of hip joint of 30 healthy male young subjects were measured using a goniometer.: 方法用关节测角器测定30例健康成年男性操练太极拳时髋关节的外展活动度。

6. The goniometer for sample, an important device, has been made and the whole experimental system is under commissioning at the present stage.: 目前关键设备全反射实验样品台已加工完成，正处于安装及系统调试阶段。

7. Method:40dry atlas specimens were used to measure anatomic data relative to screw placement technique with an electronic digital caliper and a goniometer.: 方法：用电子游标卡尺和量角器对40例干燥寰椎标本测量与进钉技术相关的解剖学数据。

8. A good result is obtained in measuring Quartz Crystal plane angle when the method is used in automatic measure& control system of X-ray diffraction goniometer.: 的自动测控系统，在对人造石英单晶切片的晶面角进行测量时，得到比较令人满意的结果。

9. The standard difference of data taken from the same person with the square goniometer by different examiner were smaller than that with the universal goniometer.: 不同测量者用方盘量角器在相同人身上测得的数据的标准差明显小于通用量角器。

10. The techniques detail measurement of both joint range of motion and muscle length testing of the spine and extremities using the goniometer, the inclinometer, and the tape measure.: 这些技术具体到如何通过量角器、测斜仪和卷尺来测量脊髓和手足部的关节活动度和肌肉长度。

11. Visual estimation, tape measurement between fixed landmarks, and the UG aligned on fixed and anatomic landmarks were compared with the CROM goniometer, which was used as the reference standard.: 视觉判断、在固定标志点弹性带子测量、解剖标志点固定通用量角器和CROM量角器比较，CROM量角器测量认为是一种参考标准。

12. The design idea of the main part of JC-1 goniometer is presented. High accuracy, good processing technology, part stiffness and stability are considered, and the instrument shape is also stressed.: 本文介绍了JC- 1型精密测角仪主体零件的设计思想，既考虑高的精度、良好的加工工艺性、零件刚性和稳定性，又注意了仪器的外形。

13. The design idea of the main part of JC-1 goniometer is presented. High accuracy, good processing technology, part stiffness and stability are considered, and the instrument shape is also stressed.: 本文介绍了JC- 1型精密测角仪主体零件的设计思想，既考虑高的精度、良好的加工工艺性、零件刚性和稳定性，又注意了仪器的外形。

热门分类

英语例句推荐