bushing

1. Master cylinder bushing at the clutch pedal.: 离合器踏板处的总泵衬套。

2. The transformer shall employ pure porcelain bushing.: 变压器采用纯瓷套管。

3. Do not remove collar bushing with valve under pressure.: 在阀门处于压力负载下，不需要拆卸轴环衬套。

4. Oil filled bushing should have plugs for test of power factor.: 充油套管应带有用于进行功率因数试验的接插头。

5. The cast iron rod bushing provides maximum load bearing support.: 铸铁连杆衬套提供最大承重的支持。

6. Align adapter bushing or gear operator (3) bore with valve stem (5).: 用阀门的阀杆(5)对准适配器衬套或持论操作机构(3)镗孔。

7. All bus and the ramus bus are covered with pyrocondensation bushing.: 所有母线和分支母线都用热缩套管覆盖。

8. The extra long bushing offers excellent load bearing characteristics.: 额外的长期套管提供出色的承载特性。

9. Bushing is one of the most important insulation parts in transformer.: 套管是变压器中一种重要的部件。

10. The adapter bushing and key may be different from illustration shown.: 适配器衬套和销键可能与图示不同。

11. The longer bronze rod bushing provides a maximum load bearing support.: 时间越长青铜连杆衬套提供最大承重的支持。

12. Tighten leaf spring press until bushing is extracted from leaf spring.: 上紧叶片弹簧加压机直到衬套被拔出叶片弹簧。

13. The longer cast iron rod bushing provides maximum load bearing support.: 铸铁的时间越长连杆衬套提供最大承重的支持。

14. The function of a bushing is to prevent metals from touching one another.: 衬套的作用是阻止金属的彼此碰撞。

15. Place Taper - lock Bushing and Timing Belt Pulley on the transmission shaft.: 将锥面紧固套与同步带轮装在传动轮上。

16. Self-lubricating rod bushing with a low coefficient of friction for smooth actuation.: 自润滑连杆衬套的低摩擦系数平稳驱动。

17. Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.: 齿轮泵主动轴与衬套磨损后，其配合间隙增大，必将影响泵油量。

18. In this, can use repair drive shaft and bushing method to recover its normal fit clearance.: 遇此，可采用修主动轴或衬套的方法恢复其正常的配合间隙。

19. That way, all movement takes place between the bushing and bearing - instead of on the bolt.: 这样，所有运动的发生之间的衬套和轴承-而不是对螺栓。

20. In this experiment, the flame stability under large bushing is better than under small bushing.: 在实验中，大套管实验工况的火焰稳定性比小套管要好。

21. The steel retaining plate has two functions, retaining the bushing and preventing rod rotation.: 固定板的钢具有两种功能，保留套管和防止杆旋转。

22. The bushing ring flange suitable temperature is decided by the designer according to the situation.: 衬环法兰的适用温度由设计者根据情况决定。

23. The designer may lower the pressure on the packing by placing a throat bushing in the pump case (Figure).: 设计者可在泵壳内放置喉道补心以降低在填料上的压力(图)。

24. The extra wide wear band is located at the furthest point from the rod bushing to support maximum loading.: 穿的超宽频段位于从套管支持最大负荷杆最远点。

25. The correctness of this algorithm is verified by the processing results of on-site data of transformer bushing.: 对变压器套管现场数据的处理结果验证了该算法的正确性。

26. Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.: 曲轴上的导向轴承：曲轴上的导向轴承一般或者是轴瓦，或者是球轴承。

27. Through development and on-board test of ZA alloy bushing, its wearing performance has been further demonstrated.: 通过ZA系列锌铝合金轴套的研制和装机试验，进一步证明其耐磨性能。

28. The kelly bushing (KB) has an inside diameter profile that matches that of the kelly, usually square or hexagonal.: 方钻杆补心的内径通常与方钻杆的外径（通常是四方钻杆或六方钻杆）相匹配。

29. Depth measurements are commonly referenced to the KB, such as 8327 ft KB, meaning 8327 feet below the kelly bushing.: 井深测量通常是指方钻杆补心高度，如补心高度8327英尺，就意味着在方钻杆补心以下有8327英尺的深度。

30. Notably no varus collapse due to bushing failure was noted despite a high percentage of high-energy unstable injuries.: 值得注意的是没有发现一例因套管失效而导致的内翻塌陷，尽管高能量不稳定性损伤占有很高比例。

热门分类

英语例句推荐