Calculation of contact pressure on TM and VAMACE premium connection casing couplings;
TM和VAMACE特殊螺纹套管接箍接触压力计算
The effect of articular step-off and neniscectomy on joint alignment and contact pressures for fractures of the lateral tibial plateau;
胫骨外侧髁骨折塌陷对关节轴线及接触压力的影响
Single chip microcomputer-based inspection of catenaries-pantograph contact pressure;
基于单片机的弓网接触压力检测
Research on contacting pressure in ball-spinning;
滚珠旋压工艺中成形区接触压力的分析计算
A pin-on-disk test rig was used to investigate the influence of sliding speed and contacting pressure on the friction and wear behavior of 45CrNi pair under dry sliding condition.
利用销盘摩擦磨损试验机,考察了干滑动摩擦条件下滑动速度、接触压力对45CrNi摩擦副摩擦磨损性能的影响。
The progressive cavity pump(PCP) distortions,forces and contacting instance of different pressure with the finite element analysis method are analyzed,the PCP two-dimension finite element model is constituted,the stress distributing correspond to the PCP stator rubber and the contacting pressure of the stator and rotor are obtained in this paper.
用有限元方法对螺杆泵在不同压力作用下的变形、受力及接触情况进行了分析研究,建立了螺杆泵的二维有限元模型,得出了在相应情况下螺杆泵定子橡胶的应力分布和螺杆泵定子与转子的接触压力。
The improving of F-ECTS is composed of three parts: analyzing the major influence factor of fretting length precision; importing force sensor to monitor the dynamic change of contact force during fretting experiment and modification of current con
微动电接触测试系统的改进将包括三部分内容:一、分析影响微动行程精度的主要因素,并提出提高精度的方案;二、引入力传感器应对微动实验过程中接触压力的动态变化,并结合力传感器改进现有系统接触压力加载与保持结构的设计;分析“四点法”测试接触电阻的四线连接可靠性的影响因素,并改进接触电阻采集记录方式,减少数据冗余。
Based on dynamic theory of roller bearing,considering variable real-time contact force and rotational velocity of roller bearing,a numerical simulation model of wearing for cylindrical roller bearing was established by the method for wear numerical simulation of components,and the wear lifetime of cylindrical roller bearing was predicted.
基于滚动轴承的动力学理论,考虑滚动轴承承受的接触压力和自转速度实时发生变化,依据零件磨损过程通用的数值仿真方法,建立了圆柱滚子轴承磨损的数值仿真模型,并对其磨损寿命进行了预测。
Considering the contact forces and safety,the comparisons were made for the simulation results to select the suitable parameters for the overhead contact line system of high-speed railway.
考虑到接触压力和运行的安全性,对不同的动态仿真结果进行比较,据此选取合适的高速接触网参数。
The effect factors of production operation on quality of welding pipe are consisted of inputting heat,welding pressure,welding speed,opening angle,seated position of inductor and resistor,geometry size and shape of roughing pipe and so on in the production process of high frequency welding pipe Holding operation process in the production is a important way for increasing the welding pipe qualit
高频焊管生产中 ,操作对焊管质量的影响因素包括输入热量、焊接压力、焊接速度、开口角、感应器和阻抗器的放置位置、管坯的几何尺寸及形状等几方面。
Consequently it is difficult to optimize the welding pressure in pressure constant mode used in conventional ultrasonic plastic welder.
为此本文利用VEP3 1 2压力控制型电气比例阀在能量模式控制的超声焊机基础上 ,首次实现了压力在焊接过程中的可变调节 ,使得焊机能够优化焊接压力 ,从而为接头质量优化奠定了硬件基础。
INFLUENCE OF TEMPERATURE ON CONTACT PRES- SURE OF CASING JOINTS
温度对套管接头螺纹接触压力的影响
Impression:(1) Pressure of the plate in contact with paper or blanket at the moment of printing.
(1)压印，（）次，（）数:（）印时，印版与纸张或胶布的接触压力。
Analysis and Research of the Presure on the Tip of Oil Seal Based on ANSYS;
基于ANSYS的油封唇口接触压力的有限元分析
Effects of the Tire/Pavement Contact Pressure on Asphalt Pavement;
轮胎接触压力对沥青路面结构的影响研究
Effect of Contact Pressure on Fretting Fatigue and Prediction of Fretting Fatigue Life;
接触压力对微动疲劳行为的影响及寿命预测
The Experimental Research of the Contact Pressure of Hydrophilic Sealing Gasket for Shield Tunnel Segments
盾构隧道遇水膨胀密封带接触压力试验研究
The Influence of the Backward Forward Movement of Pantograph on Bow-net Contact Pressure
受电弓正反向运行对弓网接触压力的影响
Research on the Influence of Axle Design Parameters on Contact Pressure between Axle and Hub
车轴设计参数对轴毂配合接触压力影响的研究
The Research of Free-contact Ultrasonic Hydraulic Pressure Measurement Method;
非接触式超声波液压压力检测方法的研究
joint contact surface
连接接触面总压紧载荷
The lug produces a "pinched" effect contact with the groove side.
极耳产生一种“压力”作用与沟槽侧边相接触。
A Method of the Printing Press & Contact Area Rate in Half-Toning Dot Printing on Fabrics
织物网点印花压力与接触面积比的关系研究
Study on Organic Wastewater Treatment by Pressurized Biological Contact Oxidation Technology;
有机废水压力式接触氧化法降解技术研究
Finite Element Simulation and Analysis of Contact and Utimate Bearing Capacity on Cable Anchor Joints;
索端冷压锚固节点接触及承载力模拟分析
Research of Equal Contact Stress Inner Curve Based on Radial Piston Motor;
径向柱塞式液压马达等接触应力内曲线的研究
Analysis and Design of Touch Mode Capacitive Pressure Sensor;
接触式电容压力微传感器的分析与设计
The Research of High-voltage Protecting System for the Catenary about the Electric Locomotive s Servicing Work;
电力机车整备作业接触网高压防护系统的研究
Multiple-wheel effect on contact behavior between hydraulic track and concrete foundation
水工轨道与基础接触压应力群轮效应分析