Pointing to the non-linearity of the FOG with the change of temperature,a method of modeling for the temperature error of scale factor with BP neural network is proposed,and it can reduce the output error of fiber optic gyroscope.
针对光纤陀螺(FOG)随温度呈非线性变化的特性,提出了采用BP神经网络对刻度因子的温度误差建模的方法,以减小光纤陀螺输出误差;用BP网络对其建模的结果和传统的建模结果进行了比较,结果表明采用BP神经网络对刻度因子的建模是非常有效的。
This paper supposed that the laser gyro scale factor is relevant to environment temperature and temperature increment, then adopts 2 inputs -3 layers BP network to set up a model .
文中先提出激光陀螺刻度因子与环境温度及温度增量有关的假设,然后采用双输入的三层BP网络建立模型,结构简单,精度高,均方差仅1。
An online identification algorithm of odometer s scale factor in land used strapdown inertial navigation system is put forward.
提出陆用捷联惯导系统中里程计刻度因子的在线辨识算法 。
Error Modeling of Scale Factor of Missile-borne
弹载开环光纤陀螺刻度因子误差建模
Is this ruler graduated in centimeters?
这把尺子是厘米刻度吗？
Influence factors of line edge roughness measured by AFM
使用原子力显微镜测量刻线边缘粗糙度的影响因素
Acceptable Error of Etching Depth in Ion Beam Etching Microlens
离子束蚀刻微透镜中蚀刻深度允许误差的研究
The numbers you specified can't be used because the interval for the minor unit tick marks must be less than or equal to the interval for the major unit tick marks.
指定的数字无效，因为次要刻度间距需小于等于主要刻度间距。
Molecular and Functional Characterization of AtCTPA1 Gene in Arabidopsis Thaliana;
拟南芥AtCTPA1基因的分子刻画及功能研究
a ruler with scales in inches and centimeters.
一把标有英寸和厘米刻度的尺子
This ruler has one scale in centimetres and another in inches
这把尺子上有厘米和英寸二种刻度。
NUMERICAL STUDIES ON ETCH PROFILES IN HIGH-DENSITY PLASMA;
高密度等离子体刻蚀轮廓的数值研究
Flow Conversion of the Gas Rotameter under Nonstandard Calibration
非标刻度气体转子流量计的流量换算
Characterization of Multiwavelet with Different Real Dilations and Translations;
具有不同伸缩和平移因子向量小波的特征刻划
Offline Calibration of BES Ⅱ Muon Detector
北京谱仪μ子计数器离线数据刻度研究
The Experimental Research of the Energy Calibration for Dayabay Neutrino Detector
大亚湾中微子探测器能量刻度的相关实验研究
Conversion of Graduation on Metal Variable Area Flow Meter Used for Steam and Process Conditions
测蒸汽的金属转子流量计刻度换算与工艺条件
Development of the Control System for High-precision Digital Electronic Engraving Machine
高精度数字电子雕刻机控制系统的研究
The numbers you specified for the axis values can't be used, because the maximum axis value must be greater than the minimum axis value.
为坐标轴指定的数值范围无效，因为坐标轴的最大刻度必须大于最小刻度。
Requirements of characteristics and calibration for personal neutron dosimeters(neutron energies less than 20MeV)
GB/T14959-1994个人中子剂量计的性能要求与刻度(中子能量小于20MeV)
A pision or an interval on a graduated scale.
分度，刻度刻度标尺上的一个间隔