Using the NC machining principles of spiral bevel gears,we explain the first-order and second-order contact conditions required by the gear tooth surface meshing.
以弧齿锥齿轮数控加工原理为基础,阐述了齿面啮合需要满足的一阶接触条件和二阶接触条件,建立了以工件齿轮转角为参数,表示铣齿刀盘中心运动与工件齿轮旋转运动关系的切齿加工运动函数。
An exact dynamic simulation of the gear mesh has come ture based on the advantage of Pro/E and ADAMS,taking the standard involute right tooth columnar gear as an example.
将Pro/E三维建模软件和ADAMS动力学仿真软件相结合,以标准渐开线直齿圆柱齿轮为例,进行了齿轮啮合的精确动力学仿真。
Comparison is made between the three kinds of bearing arrangement modes in bearing life and gear mesh.
从轴承寿命和齿轮啮合2个方面对3种布置方式进行比较。
In the elastic supporting condition, considering the influence of the elastic plate on the meshing tooth response, the dynamic model of gear supporting system and the response analytic model of meshing.
结合齿轮的实际工作状况,建立了齿轮结构的弹性体动力学模型,进行了弹性动力学分析,得出了齿轮的弹性固有特性;考虑了弹性支撑轴对齿轮体振动的影响,将其处理为弹性支撑,推导了弹性支撑弹簧刚度的表达式,并在弹性边界条件下,考虑了弹性圆盘对啮合齿响应的影响,建立了齿轮支撑系统的动力模型和轮齿响应计算模型,研究了齿轮支撑系统的固有特性,并与实验结果进行了对比验证;求解了啮合齿的动力学响应,并进行了模拟仿真。
The machining errors of gear that relate to the nature of involute are studied with gear engagement theory and combining grinding-machining in this paper and they are summarized as transmissio.
本文综合运用了齿轮啮合理论，并以磨齿加工为例，系统地研究了与渐开线性质有关的齿轮加工误差产生的啮合机理，并将其概括为传动误差、回转轴相对位置误差及刀具误差。
Method about determining mating tooth number of harmonic chain-drive and load on wheel tooth;
谐波链传动的啮合齿数及轮齿上载荷的确定方法
One cog-wheel engages with another.
一齿轮与另一齿轮啮合.
dual flank gear rolling tester
双面齿轮啮合检查仪
bevel gear mesh adjusting gasket
锥齿轮啮合调整衬垫
The two cogwheels are engaged.
这两个齿轮啮合在一起。
gear meshing error meter
齿轮啮合误差测量仪
straight spur gear-on-gear pump
圆柱直齿[外啮合]齿轮泵
A small cogwheel that engages or is engaged by a larger cogwheel or a rack.
小齿轮，齿杆啮合大齿轮或被大齿轮或齿条啮合的小齿轮
The engagement of gear teeth.
啮合齿轮的互相咬合
internal spur gear
内啮合圆柱齿轮，直齿内齿轮
gear single flank rolling tester
齿轮单面啮合检查仪
Gears that are not meshing properly.
没有很好啮合的齿轮
final drive with external gear
外啮合齿轮最终传动
quiet internal gear pump
低噪声内啮合齿轮泵
gear two flank rolling tester
齿轮双面啮合检查仪
one-flank gear rolling tester
单面啮合齿轮检查仪
gear wheels that mesh in the same plane.
啮合在同一平面的齿轮。
The cogs don't quite mesh.
这些轮齿啮合不严.
gears that mesh at an angle.
齿轮以一定角度啮合。