The paper analyzes and designs the main circuit of high-power IGBT inverted air plasma cutting power supply.
对一种大功率IGBT逆变式空气等离子切割电源的主电路进行了原理分析与设计。
Focusing on characteristics of inverted plasma cutting power supply with nonlinearity,time variability and hybrid property,a simulation model of digital inverted cutting power system based on PI adjustment was put forward.
采用基于Simulink的元件仿真技术,针对逆变式等离子弧切割电源本身具有非线性、时变性及混杂性特点,建立了基于PI调节的数字化逆变式切割电源系统仿真模型。
Improvement of wire frame in HS-WEDM;
高速走丝电火花线切割机线架结构的改进
The software realization of serial communication for multi-WEDM machines;
电火花线切割机多机串行通讯软件的开发
The development trend and applications about WEDM machine arc pointed out.
本文详细分析总结了现有低速走丝电火花线切割机走丝系统的组成、功能及原理,在分析现状的基础上,指出了其应用及发展趋势。
The high-frequency pulse waveform of WEDM pulse generator was analyzed. Basic condition method is presented the results is well.
分析了电火花线切割机脉冲电源的高频脉冲波形，提出了有效的控制方法，获得了良好的综合效果。
Research on WEDM Pulse Power Supply Based on ISA Bus;
基于ISA的电火花线切割脉冲电源研究
Research on Improving the Main Control Circuit Based on the Pulse Power Supply of Electric Spark Line Cutting Machine
基于电火花线切割机床脉冲电源的主控电路改进研究
Research on Bidrectional Narrow Pulse Generator of Non-Resistance for WEDM;
往复走丝线切割窄脉宽无阻脉冲电源的研究
Research on Micro Energy and Controllable Pulse Power Supply for MWEDM;
微能可控微细电火花线切割脉冲电源的研究
Study on Energy-Saving Pulse Generator for WEDM;
电火花线切割加工节能脉冲电源的研究
DESIGN FOR INTERRUPT ACCESS OF DEVICE DRIVER OF NON-RESISTANCE PULSE GENERATOR FOR WIRE ELECTRICAL DISCHARGE MACHINING BASED ON WDM;
基于WDM的电火花线切割无阻脉冲电源中断驱动程序设计
Research of Digital AC Voltage Controller Technology for LS-WEDM;
低速走丝线切割脉冲电源数字化交流调压技术研究
The Study of Processing the Waste Water Emulsion of Linear Incision by the Method of Pulse Electroflocculation and Chemical Coagulation;
脉冲电絮凝法和化学混凝法处理线切割乳化液废水的研究
The Study and Design on Pulse Standard Signal Generator for LSWEDM
慢走丝线切割机床脉冲基准信号发生器的研究与设计
The Study on Pulse Generator for LSWEDM
低速走丝线切割机床脉冲基准信号发生器的研究
NC EDM wire-cut machine
电火花数控线切割机床
NC wirecut EDM machine
数控电火花线切割机床
taper wire-cut EDM machine
锥度电火花线切割机床
super CNC wirecutting machine
电火花数控线切割机
The Design of Power Source of Linear Motor Based on Bilateral Pulse Variable Frequency Control;
双向脉冲变频控制直线电机电源的研究与设计
Study on the Control Technology of Isopulse with WEDM;
线切割加工中等能量脉冲控制技术的研究
Discuss on Multi-Times Cutting Technology of Move Back and Forth Run-Wire WEDM
往复走丝电火花线切割机床多次切割技术探讨