She speaks with a soft West Country burr.
她说话带有一种西部地区浓重 r 音的口音。
1.伯尔
2.粗磨(刀)石
3.(铜版等的)粗刻纹,锯齿状刻纹
4.【机】毛口,毛头
5.钻孔锥;(牙科用的)磨锥
6.同“bur”
7.【机】垫圈;(冲孔机冲下的)金属小圆片
8.(月)晕,光圈
9.(木材的)瘤部木纹;【矿】坚硬石灰岩
10.(发"r"音时小舌颤动的)粗喉音;粗浊的发音
11.嘎嘎声,吓吓声
1.伯尔
2.粗磨(刀)石
3.(铜版等的)粗刻纹,锯齿状刻纹
4.【机】毛口,毛头
5.钻孔锥;(牙科用的)磨锥
6.同“bur”
7.【机】垫圈;(冲孔机冲下的)金属小圆片
8.(月)晕,光圈
9.(木材的)瘤部木纹;【矿】坚硬石灰岩
10.(发"r"音时小舌颤动的)粗喉音;粗浊的发音
11.嘎嘎声,吓吓声
1.用粗喉音说(话)
2.用粗喉音说话,发音粗浊
1.Same as bur
2.the part of some plants that is covered all over with pricklessmall sharp parts and contains the seed
3.a way of pronouncing English where the “r” sounds can be heard more strongly than in the standard way of speaking
1.After twenty years as a teacher, Mr Burr called it a day and retired.
做一名教师做了二十多年，伯尔先生决定到此为止，退休了。
2.Burr might have been the president instead of vice president, had it not been for Hamilton's interference.
如果不是汉弥尔顿的介入，安伦波当时可能成了美国总统，而不是副总统。
3.Bakery boss to see him over, cordial, said: "Little Burr, today what you want bread? "
面包坊的老板见他过来，亲切的说：“小伯尔，今天想吃什么面包？”
4.Burr, the dust particles in the fixed network is possible when punctured whee caused the rupture of the mesh fabrics complete Board.
毛刺、沙粒在固网时有不定会刺破网布变成整板网布的分裂。
5.Once again retract the burr hole site, and fold back the Micro Sensor completely at the desired bend side to leave a kink in it.
再次收缩单孔处，在指定段将微传感器完全弯曲并留下一个扭结。
6.should be installed in the burr, clean and remove the stolen goods, do not make it into the pipe to prevent blockage of the trachea.
安装时应将毛刺、赃物去除干净，不要使其流入管道，以免堵塞气管。
7.The surface of the syringe must be clear and pure; rough edge, burr, plastic stream, defect are not allowed.
注射器表面必须清洁无杂质，不得有毛边、毛刺、塑流、缺损等缺陷。
8.The burr in the surface and grooves can be eliminated obviously thus getting a high surface precision and smooth finish.
有效地去除换向器表面及槽口的毛刺，提高其表面精度和光洁度。
9.Even if the lifespan is known as the Tie Shan Hui Kwong Kam, although the tail of a burr, but the actual view is also very beautiful.
即便是被称为铁扇的寿惠广锦，虽然尾部有毛刺，但是实际看来也是很漂亮的。
10.The Si-Mn steel track plate and pin usually exist the early abrasion, one of the main reasons is the burr defect of pin hole.
硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。