Virtual designing and the craft analysis of the hinge cup seat pressing mold;
铰链杯座的冲压模具虚拟设计及工艺性分析
Die forging technique and design of die for hinge mount;
铰链座模锻成形工艺分析与模具设计
The paper introduces the hinge mount forming process, designs forming die structure, and analyzes the die working process and main designing points.
介绍了铰链座的成形工艺 ,设计了弯曲成形模的结构 ,分析了其模具工作过程和模具设计要点。
The technological property of the hinge pedestal part is analyzed.
分析了铰链支座的工艺性 ,详细介绍了级进模排样方案和总体结构 ,阐述了关键部件的设计计算方法。
The slip spheric joint support is also used for the large-span steel structure roofing in order to dispel distortion by temperature change an.
为了消除温度变形和安装允许误差的影响,对大跨度钢结构屋面在支座部位采用了滑动球铰支座。
carbide tipped valve seat reamer
硬质合金气门座铰刀
In this paper, the construction method for the hinged steel bearings and hinged sliding plate bearings specially designed for the Bridge is presented.
介绍针对本桥专门设计的铰轴钢支座和铰轴滑板钢支座施工方法。
Installation Technologies of Preburied Prestressed Anchor Bolts of Wide Diameter Pin Roll Hinge Supports
预埋预应力锚栓的大直径销轴铰支座安装技术
Influence of Support Means of Hinge-Bearing for Container Crane's Boom on Lateral Vibration
岸桥前大梁铰支座支承对其横向振动的影响
The Numerical Simulation of Damage to Hinge Joints and Bridge Bearings for Fabricated Reinforced Concrete Hollow Pangyo
装配式钢筋混凝土空心板桥支座与铰缝损伤的数值仿真分析
Wind-induced lateral vibration of a 7500t floating crane's boom considering axial clearance between boom and pin hinge
7500t浮吊臂架考虑铰支座间隙的风致横向振动研究
A glass frame that is placed on the wooden frame, inside it there is a little frame covered by sponge, with two hinges at the lower parts of the little frame.
木座上置有一个大玻璃框架，玻璃框架中央有一个被海棉遮掩著的小窗，小窗下有铰位。
Hardfaced seating surfaces, large diameter hinge pins, and corrosion resistant bearing surfaces help lengthen operating life in tough surfaces.
经过硬面处理的阀座表面，大直径铰链销，以及防腐蚀轴承表面，有助于延长坚硬表面的使用寿命。
Fit hinge 5 into the opening in the machine bed, and fit the machine head to table rubber hinge 6 before placing the machine head on cushions 7 on the four corners.
把铰链5放到机台的孔上，对准台板橡胶支座6，把头部放到四角的机头胶垫7上。
and the other two rubber cushion seats 3 on the hinge side B are fixed by using a rubber-based adhesive. Then, oil pan 4 is placed.
再用螺钉2把铰链侧B的2个头部胶垫座3钉好固定，然后把底槽4放上去。
Jinmao" Company is located in Yanguan Industrial Zone, Haining, Zhejiang on the banks of the Qiantang River. It is a specialized manufacturer of drawer sliding rails, hinges, goods shelves.
金茂”公司座落在钱塘江畔——浙江海宁盐官工业区，是一家抽屉滑轨，铰链、架的专业制造企业。
To attach by or equip with or as if with hinges or a hinge.
给…装铰链，用铰链接合
" Aluminium stranded conductors and aluminium conductors,steel-reinforced"
GB1179-1983铝铰线及钢芯铝铰线
Articulator Installation and Process Requirement of 6181S02 Articulated Bus
6181S02铰接客车铰接部分安装及工艺要求
Experiment and Study on the Pivoted Pin Strength and the Stress Near the Pivot-Point of Articulation System of Wheel Loader
装载机车架铰接系统铰销强度及铰点附近应力分布的试验研究
brass-plated iron square hinge
镀黄铜抽心铁方铰链
spiral flute machine reamer with straight shank
螺旋直柄槽机用铰刀
spiral fluted expansion hand reamer
螺旋槽可胀式手铰刀